Best Mini-ITX Cases for a 4- to 8-Drive NAS

Compare five Mini-ITX NAS cases for four to eight 3.5-inch drives, including cooling, hot-swap access, power supplies, compatibility and real build costs.

Quick Summary (TL;DR):
For a four- or five-drive NASPriceAliExpress price, the Jonsbo N2PriceAliExpress price is a compact choice if you accept a 65 mm CPU-cooler limit and one low-profile expansion slot. For six internal hard drives without a hot-swap requirement, the Fractal Design Node 304Price offers six combined 3.5/2.5-inch mounts, three included fans, a full-size ATX PSU and room for a 165 mm CPU cooler. For eight 3.5-inch drives, the Jonsbo N3AliExpress price is our most balanced compact pick on published specifications: eight HDD bays, two included 100 mm drive-chamber fans and 130 mm cooler clearance, although its SFX PSU must be no longer than 105 mm. The SilverStone DS380 is an alternative when eight front-accessible hot-swap trays are essential, but its 57 mm cooler limit and dense drive cage demand careful thermal planning. The Jonsbo N4 is a useful six-HDD option if you may move to micro-ATX. The right case is the one that fits your actual drives, SATA/HBA connections, PSU cables, cooling and maintenance routine—not simply the one with the most advertised bays. This is a specification-based buying guide, not a hands-on case test; regional stock and revisions must be checked before ordering.

The best 4- to 8-drive Mini-ITX NAS cases at a glance

Case3.5-inch HDD baysAdditional 2.5-inch mountsMotherboardPSUCPU cooler limitOur use-case verdict
Jonsbo N251Mini-ITXSFX ≤150 mm65 mmSmall five-disk NAS; low-profile card only
Fractal Node 3046 shared 3.5/2.5 mountsNo separately promised mountsMini-ITX / Mini-DTXATX165 mmSix-disk DIY build; straightforward cooling; no hot-swap
Jonsbo N462Mini-ITX / micro-ATXSFX ≤125 mm70 mmSix HDDs plus SSDs; larger board options
Jonsbo N381Mini-ITXSFX ≤105 mm130 mmEight-disk compact NAS; check cabling
SilverStone DS3808 hot-swap 3.5/2.54 fixed 2.5Mini-ITX / DTXStandard-depth SFX57 mmEight front trays; plan for tight cooling and cable routing

Drive counts are manufacturer-specified physical mounting positions, not a guarantee that a particular motherboard can connect them all. A case with eight bays still needs eight compatible data connections, adequate 12 V spin-up power and the correct backplane/cable arrangement. A shared 3.5/2.5-inch mount holds either size, not both simultaneously. The Jonsbo N4 has six 3.5-inch positions and two separate 2.5-inch positions: its “eight drives” headline must not be interpreted as eight 3.5-inch disks.

Our shortlist deliberately excludes the older Jonsbo N1 as a primary 2026 recommendation because the manufacturer lists it in its end-of-life case range; second-hand units can still be useful, but availability and replacement parts are a different buying decision.

Which case should you buy? A quick decision guide

  • Four drives now, perhaps five later: choose the N2 if small footprint matters and your CPU cooler, motherboard headers and expansion card fit. Leave one 3.5-inch position unused initially for easier growth.
  • Four to six drives, low cost and easy fan replacement: start with the Node 304. It is not hot-swap, but ATX PSU compatibility and its three included fans are meaningful practical advantages.
  • Six HDDs with a micro-ATX upgrade route: shortlist the N4. A micro-ATX board can offer more expansion slots, but the case still has a 70 mm CPU cooler ceiling and an SFX power supply.
  • Eight HDDs in a genuinely small footprint: choose the N3 if its short SFX PSU and storage-cabling requirements suit your build.
  • Eight disks with front hot-swap trays: consider the DS380 if you are willing to validate drive temperatures under sustained load and accept a low-profile CPU cooler.
  • Need more than eight 3.5-inch HDDs or several full-height PCIe cards? A larger micro-ATX/ATX chassis may be cheaper and easier to maintain than forcing the build into Mini-ITX.

Jonsbo N2: a compact five-bay NAS for modest CPUs

The official Jonsbo N2 specifications list a 222.5 × 222.5 × 224 mm enclosure, five 3.5-inch HDD positions and one 2.5-inch SSD position. It accepts Mini-ITX motherboards, an SFX PSU up to 150 mm long, a CPU cooler no higher than 65 mm and one single-slot, low-profile expansion card. Jonsbo includes a slim 120 × 15 mm fan for the drive area.

This is attractive for a low-power storage-first NAS with integrated graphics, modest CPU heat and an M.2 boot SSD. A Mini-ITX motherboard with four SATA ports plus an appropriate additional controller can serve five HDDs, but do not assume that an M.2-to-SATA card or PCIe HBA will fit without checking its height, cable exit and the single available expansion slot.

What can go wrong: a tall tower cooler will not fit; a full-height HBA bracket is wrong for the slot; and a slim fan does not magically guarantee acceptable temperatures for five densely packed high-capacity drives. Measure HDD temperature during parity checks or scrubs, not only when the NAS is idle. A drive-cage fan upgrade may be worthwhile, but check thickness, mounting and airflow direction first.

Who should buy it: users who value a small, tidy five-disk NAS more than broad PCIe expansion or high-performance CPU cooling. It is less appealing if your future plan requires a full-height 10GbE card and a separate disk controller.

Fractal Design Node 304: six drives, an ATX PSU and proper cooler clearance

The Fractal Node 304 product page specifies six combined 3.5/2.5-inch drive mounts, Mini-ITX/Mini-DTX board support, an ATX PSU, up to 165 mm CPU cooler height and three included fans: two 92 mm front intakes and a 140 mm rear fan. The enclosure measures 374 × 250 × 210 mm and uses removable drive brackets.

The Node 304 is particularly sensible for an owner who expects to open the chassis only occasionally. A standard ATX PSU can be easier to source than a short SFX model, and the large CPU-cooler clearance broadens the choice of quiet air coolers. Its drive mounting is internal, not hot-swap; replacing a failed disk requires powering down as appropriate, opening the case and removing brackets.

Its headline GPU clearance does not apply unconditionally to a six-drive NAS: Fractal explains that longer graphics cards require removing drive brackets. Likewise, the real PSU length and cable exit matter when a modular ATX unit sits beside the drive assembly. Fractal also warns that certain right-angled motherboard SATA connectors may conflict with installation; inspect the exact board layout before ordering.

Who should buy it: the home-lab builder who wants four to six HDDs, an ordinary ATX PSU, straightforward fan access and enough CPU cooling for containers or light virtualisation. Choose something else if you need eight HDDs or routine front-accessible drive swaps.

Jonsbo N4: six hard drives plus SSDs, with micro-ATX support

The Jonsbo N4 manufacturer page specifies six 3.5-inch HDD bays plus two 2.5-inch SSD bays, Mini-ITX or micro-ATX motherboards, four PCI expansion positions, an SFX PSU up to 125 mm long, a 70 mm CPU-cooler limit and one included 120 mm fan. Its published dimensions are 286 × 300 × 228 mm.

The extra motherboard space is its real advantage. With micro-ATX, you may be able to combine a SATA HBA and faster network adapter rather than choosing which one gets the sole Mini-ITX expansion slot. However, a micro-ATX board still needs suitable PCIe slot spacing, chipset lanes and a chassis-compatible card height. The case uses low-profile expansion-card geometry, so a full-height bracket should not be assumed to fit.

Do not confuse six HDDs plus two SSDs with eight HDD bays. Also, the manufacturer headline does not establish that every drive position has the same hot-swap mechanism. Confirm the exact front/backplane arrangement and revision with the installation manual or seller before purchasing for a live-service replacement workflow.

The single included 120 mm drive-area fan is a starting point, not proof of eight-drive cooling headroom. For a full six-HDD build, check inlet clearance and log drive temperatures during a sustained sequential workload. The N4 is a strong option for an owner who wants the motherboard flexibility of micro-ATX without moving to a conventional tower.

Jonsbo N3: eight 3.5-inch drives without a large tower

The official Jonsbo N3 product specification lists eight 3.5-inch HDD bays and one additional 2.5-inch SSD position, Mini-ITX board support, two expansion slots, a 130 mm CPU-cooler limit and an SFX PSU no longer than 105 mm. Dimensions are 233 × 262 × 298 mm. Jonsbo lists two included 100 × 25 mm fans in the disk compartment and two optional 80 × 25 mm fans in the motherboard compartment.

Compared with the N2, the N3 is much more accommodating for CPU cooling and drive count, although it is less forgiving about PSU depth. That short SFX limit is easy to miss: some units sold as “SFX” have longer housings or stiff modular cable plugs. Check the exact PSU drawing, the distance to the drive/backplane wiring and whether the required modular sockets face a restricted area.

An eight-drive NAS also forces a data-path decision. Most consumer Mini-ITX boards do not provide eight native SATA connectors. You may need a suitable HBA, an onboard controller designed for NAS use, or a carefully verified PCIe/M.2 storage adapter. Count usable ports after any M.2/SATA sharing restrictions. The HBA may occupy the only practical full-height PCIe position, leaving 10GbE networking dependent on the motherboard.

Who should buy it: a serious eight-HDD home storage builder who can validate short SFX PSU compatibility and plans disk connectivity before buying. For eight drives, it is our most balanced compact option on published cooler and fan specifications; that is not a claim of measured superiority over the DS380.

SilverStone DS380: eight front hot-swap bays, with tighter thermal constraints

The SilverStone DS380 provides eight front hot-swappable 3.5/2.5-inch SAS/SATA trays plus four fixed internal 2.5-inch mounts, Mini-ITX/DTX motherboard support, an SFX PSU and three included 120 mm fans. Its dimensions are approximately 211 × 360 × 285 mm, with a particularly restrictive 57 mm CPU-cooler ceiling. These details are documented in the SilverStone-authored DS380 user manual (PDF) and regional product specifications.

The removable trays are useful when a failed disk must be replaced without dismantling the chassis. But hot-swap is a whole-system feature: the drive controller, backplane, SATA/SAS configuration, operating system and storage-management procedure must all support the intended replacement. A SATA motherboard port does not become a SAS controller merely because the backplane accepts SAS drives.

The manual has an important electrical instruction: the DS380 backplane has multiple power inputs, and SilverStone advises against feeding all of them from one PSU cable. Follow the exact manual for your revision, use suitable independent PSU cable runs, and avoid improvised high-current splitters. It also documents tight component clearances that matter when the main drive cage is fully occupied.

For a dense eight-drive array, pay special attention to airflow around the front cage. Do not assume that three included fans mean the middle HDDs will remain cool during a lengthy resilver or parity check. Record each disk’s SMART temperature, adjust fan curves and check whether cabling blocks the intake path. Regional stock may be limited for this older model, so confirm availability, accessories and returns before ordering.

Who should buy it: someone who values eight front-accessible trays more than tall CPU coolers or flexible cable routing, and is prepared to verify thermals and backplane wiring carefully.

Drive bay count is only the first compatibility check

Motherboard ports and the expansion-slot trap

A Mini-ITX board is roughly 170 × 170 mm and normally offers one PCIe expansion slot. That creates a trade-off in storage servers: an HBA for six or eight SATA/SAS drives may consume the slot you wanted for 10GbE. Micro-ATX can offer more physical slots, but the CPU/chipset still has finite PCIe lanes and some board slots may run at lower electrical widths.

Before buying a case, draw a connection map. Record every planned HDD, the boot SSD, any cache SSD, the board’s SATA ports, M.2 slots, PCIe slots, any shared-port restrictions and the network interface. The case does not fix a shortage of SATA ports.

Example eight-drive connection plan (illustrative):
8 x 3.5-inch HDD --> 8 controller ports (HBA or verified onboard controller)
1 x boot SSD      --> M.2 or independent SATA port
1 x network link  --> onboard 2.5GbE / 10GbE if PCIe slot is used by HBA

Verify: motherboard lane sharing + HBA bracket height + case cable path.
Never assume an M.2-to-SATA adapter works in every M.2 socket.

For a fuller discussion of whether to build or buy, see DIY NAS vs Prebuilt NAS: Complete Build and Running Costs. That guide covers system architecture; this page concentrates on the chassis and physical fit.

Backplane, connector type and data-cable routing

A backplane can make drive removal much easier, but introduces connectors, power distribution and sometimes additional failure points. Inspect whether a case requires individual SATA data leads, a Mini-SAS breakout harness or another documented connection. Connector shapes and pinouts are not interchangeable merely because the names sound similar. Do not order “SAS cables” generically; match the controller-side and backplane-side connector standards and cable direction.

An ordinary SATA motherboard cannot directly operate a SAS-only HDD. A SAS-capable HBA can usually work with compatible SATA disks, but the actual backplane, cabling and controller firmware still need verification. If you are using TrueNAS or Unraid, check that the controller exposes individual disks reliably rather than presenting an opaque hardware RAID volume.

Plan cable bend radius before installing the board. Dense Mini-ITX cases often put SATA power connectors or fan frames immediately behind the drive cage. A technically compatible connector that cannot be plugged in without crushing the cable is not a usable configuration.

SFX, SFX-L and ATX PSU fit

A PSU form factor is not a universal length guarantee. The N3 specifies a particularly short SFX unit (≤105 mm); the N4 specifies ≤125 mm; the N2 permits SFX up to 150 mm; the Node 304 accepts ATX; and the DS380 manual calls for a standard-depth SFX supply. Do not substitute an SFX-L PSU merely because its mounting screw pattern resembles SFX. Even when the PSU chassis fits, modular cable plugs may not.

Calculate electrical requirements from the drives’ documented 12 V start-up current, CPU load, fans and controller. Several HDDs may spin up together after a power restoration, creating a short peak much higher than idle consumption. Look for staggered spin-up support only if the actual controller, disks and firmware implement it; do not assume it exists. Prefer a reputable PSU with adequate connectors and headroom over an oversized unit bought solely for its wattage sticker.

CPU-cooler height and RAM interference

The gap between a 57–70 mm cooler limit and a 130–165 mm limit changes the entire CPU-cooling choice. A low-profile cooler may be adequate for an efficient CPU, but a hot processor running continuous transcoding or virtual machines could be a poor match for the smallest chassis. Check the cooler’s total installed height, RAM clearance, socket position and whether the fan can draw air through the case rather than recirculating warm air.

The case maker’s maximum is a physical ceiling, not a recommendation to buy a cooler exactly that tall. Leave tolerance for manufacturing differences, fan clips and nearby cables. A server that operates quietly at idle can still throttle under a long parity rebuild if the CPU and HDD chamber compete for airflow.

Cooling eight NAS drives: airflow beats cosmetic compactness

Hard drives generate heat even when CPU use is low. Closely packed 3.5-inch drives need a clear intake path, a predictable exhaust route and enough static pressure to move air through cages and filters. A large fan behind an obstruction may deliver less useful airflow than a smaller fan with a clean path.

  • Measure per-drive temperature: use SMART temperature readings and identify the hottest bay, not the array average. Drive vendor operating limits differ by exact model; check the datasheet rather than using one universal threshold.
  • Test a real sustained task: parity checks, RAID scrubs, resilvering and large backups stress disks longer than opening a file. Log temperatures after the chassis reaches thermal equilibrium.
  • Control dust: clean filters without blocking intake; a heavily restricted filter can worsen HDD temperature even when it reduces dust.
  • Watch vibration: tighten drive carriers correctly, avoid loose metal contact and use approved mounting hardware. Resonance may be more noticeable with six to eight HDDs than with two.
  • Keep cables out of the airflow path: especially thick PSU looms and SATA bundles directly in front of fan intakes.
  • Do not silence fans blindly: a quiet curve that is acceptable with two HDDs may be unsafe after adding four more. Set curves using observed temperatures.

A useful practical method is to log each disk at idle, during a long read or scrub, and after the load stops. If the centre drives are consistently much warmer than edge drives, inspect airflow distribution and drive spacing before buying a faster CPU or a quieter fan. We have not measured these five chassis, so no temperature rankings are presented as test results.

Hot-swap versus internal mounting: what actually matters?

QuestionFront-accessible hot-swap caseInternal drive-mount case
Failed drive replacementPotentially faster tray access; still follow OS/controller procedureUsually requires opening case and planned power-down
Backplane complexityAdditional PCB/connectors and power distribution to verifyUsually direct drive cables; fewer intermediary connectors
CoolingDense front trays may restrict airflow; test each bayCan offer more open airflow but depends on case
Noise and vibrationTray latches and cage resonance may need attentionMounting brackets can be secure but more fiddly
Best fitFrequently serviced arrays and accessible racksHome NAS with infrequent disk replacement

Hot-swap is not the same as “pull any disk at any time”. In a redundant array, first identify the failed drive by serial number, confirm the array can tolerate removal, and follow the NAS operating system’s replacement procedure. Removing a healthy disk from a degraded array can cause avoidable data loss. RAID is not a backup.

A build checklist before ordering a 4-, 6- or 8-drive case

Component or checkFour/five-drive buildSix-drive buildEight-drive build
HDD capacity plan4–5 bays; consider one free6 bays; decide whether all filled now8 bays; verify future replacement access
Data ports4–5 usable SATA/SAS connections6 usable ports or a verified HBA8 verified controller ports plus boot storage
Motherboard expansionMini-ITX slot may be spareHBA may occupy only slotHBA/network conflict likely on Mini-ITX
PSUCheck cable count and start-up drawCheck SFX/ATX depth and loomCheck 12 V headroom and backplane feeds
FansOne drive fan may be sufficient only after testingCheck drive-centre temperaturesSustained scrub thermal test essential
BackupSeparate backup target and restore testCapacity/retention sized to protected dataBudget external or second-NAS/off-site copies

For hard-drive choice, CMR vs SMR for NAS explains why recording technology matters for some rebuild and write-heavy workloads. NAS Drive Compatibility is useful when comparing a DIY chassis against a commercial NAS ecosystem.

What does a complete Mini-ITX NAS actually cost?

A case is only one line in the bill of materials. For a fair purchase decision, include the motherboard/CPU, memory, boot SSD, HDDs, PSU, additional fans, controller/cables, UPS and a backup target. Prices change frequently by region, so the following is an illustrative budgeting exercise in pounds, not a current retail quotation. It uses the same hypothetical £150 price per 8 TB HDD to isolate how the drive count affects the total. It does not imply that any specific model is currently sold at these amounts.

Illustrative budget itemFour HDDsSix HDDsEight HDDs
Chassis£110£135£180
Motherboard and CPU£210£230£300
RAM£65£75£90
Boot SSD£55£60£70
Compatible PSU£85£100£110
8 TB HDDs at hypothetical £150 each£600£900£1,200
Fans, HBA/cables allowance£40£55£85
UPS allowance£140£160£180
Separate backup allowance*£180£240£300
Illustrative upfront total£1,485£1,955£2,515

*Important backup caveat: the example backup allowances are placeholders, not a claim that one inexpensive external drive can protect the full array. A six- or eight-disk NAS with tens of terabytes of important data may need a much larger second NAS, several rotating disks or cloud storage, potentially costing far more. Size backups from the data actually protected, retention and restore objectives. See Best External Hard Drives for NAS Backups for a separate-drive approach.

The capacity you can use also depends on redundancy. As a simple illustration, six 8 TB drives in a dual-parity layout have roughly 32 TB of nominal data capacity before filesystem overhead, reserved space and differences between TB and TiB. This is not an estimate of actual usable capacity for every RAID implementation. Plan the pool and backup requirements before deciding whether you need six or eight bays.

Five-year electricity costs: measure rather than assume

The case itself does not have a fixed “watts” rating. Fans, drive models, PSU efficiency, CPU platform and workload determine wall consumption. If the complete NAS averages 30 W, 45 W or 60 W at the socket, and the illustrative electricity rate is £0.30/kWh, the five-year cost is:

5-year electricity cost = (average watts / 1,000) × 8,760 × 5 × £/kWh

30 W × 43,800 hours / 1,000 × £0.30 = £394.20
45 W × 43,800 hours / 1,000 × £0.30 = £591.30
60 W × 43,800 hours / 1,000 × £0.30 = £788.40

These wattages are scenarios, NOT measured results for the cases above.

At that illustrative tariff, every extra continuous watt adds £13.14 over five years. Buying a £50 more expensive case because it fits a more efficient PSU or enables better thermal behaviour may pay off, but only if you measure a real difference. A larger case does not inherently consume more electricity. Remember that HDD replacement, UPS batteries, off-site backup fees and hardware failures are additional ownership costs.

Practical assembly order that avoids expensive mistakes

  • Before the purchase: draw a scale-free component layout showing PSU length, CPU cooler, motherboard SATA port orientation, PCIe bracket, HDD backplane and every cable exit.
  • Bench-test the platform: update BIOS/UEFI as needed, confirm RAM stability, identify SATA/HBA ports and boot the intended NAS OS with one test disk before populating the case.
  • Install the PSU and motherboard: route EPS/ATX power cables first in cramped enclosures; later access may be blocked by the drive cage.
  • Connect the drive backplane: use the manufacturer-specified power inputs and approved cables. For the DS380, follow the manual’s guidance on distributing power across PSU leads.
  • Label every HDD: record bay number, model and serial number in a simple spreadsheet or label scheme. A “disk 3” warning is not enough if you cannot identify the physical disk.
  • Populate and validate: confirm every disk is visible individually, SMART data can be read and the OS reports no cabling or controller errors.
  • Run a thermal soak: complete a long read/scrub while logging per-drive temperature, fan behaviour, CPU thermals and system stability.
  • Prove recoverability: set up a separate backup and perform a small restore before relying on the NAS for irreplaceable files.

If a disk intermittently disappears, investigate its SATA data lead, backplane connector, power feed and controller logs before assuming the HDD itself is faulty. If temperatures rise only during sustained activity, prioritise airflow and fan control rather than simply changing the filesystem. If a PSU trips during boot with many disks, check the drive spin-up current and PSU/cable distribution.

Common buying mistakes with compact NAS cases

  • Buying for a “drive count” rather than drive size: six 3.5-inch HDD mounts and two 2.5-inch SSD mounts are not eight HDD bays.
  • Assuming every hot-swap backplane supports SAS: verify both the drive type and the controller; SATA ports do not directly support SAS-only drives.
  • Ignoring PSU length: a standard SFX PSU that fits the N2 may exceed the N3’s published 105 mm limit.
  • Using a full-height HBA in a low-profile slot: the card and its bracket must both fit; a flexible riser is not an automatic solution.
  • Counting M.2 SATA adapters as guaranteed ports: board socket wiring, lane sharing, boot support and controller drivers vary.
  • Planning to install a long GPU while filling every drive bracket: some chassis achieve GPU clearance only by sacrificing disk positions.
  • Choosing a low-RPM fan curve before testing: sustained array rebuilds can heat central HDDs more than everyday file browsing.
  • Forgetting the backup: parity protects against some drive failures, not accidental deletion, ransomware, theft or fire.

Frequently Asked Questions

What is the best Mini-ITX NAS case for four drives?

If you are likely to expand to five drives and want the smallest enclosure, the Jonsbo N2 is a practical shortlist choice. If you prefer a standard ATX PSU, larger CPU cooler and up to six internal mounts, the Fractal Node 304 is usually the more flexible path. Choose based on actual parts fit, not empty bays alone.

Which Mini-ITX NAS case supports eight 3.5-inch hard drives?

The Jonsbo N3 and SilverStone DS380 both specify eight 3.5-inch positions. The N3 offers greater published CPU-cooler height; the DS380 emphasises front hot-swap trays and also provides four additional fixed 2.5-inch mounts. Neither eliminates the need for eight controller ports and suitable power cabling.

Is the Jonsbo N4 an eight-bay HDD case?

No. Its manufacturer specifications distinguish six 3.5-inch HDD positions and two 2.5-inch SSD positions. It can hold eight drives only if two of them use the separate 2.5-inch mounts.

Does hot-swap mean I can remove any drive while the NAS is running?

No. The chassis may permit physical insertion and removal, but safe replacement depends on the controller, OS, pool redundancy and the specific drive being replaced. Follow the storage OS procedure and identify the correct serial number first.

Do I need a dedicated HBA for six or eight SATA hard drives?

Not always. A motherboard with enough independently usable native SATA ports can be sufficient. Otherwise a properly supported HBA or other verified controller may be necessary. Check PCIe lane sharing, controller firmware, disk visibility and whether the expansion card physically fits the case.

Will a NAS case with more fans always be quieter?

No. Fan quality, speed, static pressure, restrictions and HDD vibration all matter. A larger, slower fan can be quieter than a small high-speed fan, but a poorly positioned fan may not cool the centre disks. Measure both noise and disk temperature under realistic load.

Can I use an ordinary desktop ATX power supply?

Only if the chassis supports it. The Fractal Node 304 does; the Jonsbo N2/N3/N4 and SilverStone DS380 require specified SFX dimensions. Check PSU depth and modular cable clearance in addition to mounting compatibility.

How much capacity do six 8 TB drives provide?

They provide 48 TB of raw manufacturer-labelled capacity. Usable storage depends on redundancy and formatting. A two-drive-equivalent parity configuration yields roughly 32 TB nominal before filesystem overhead and TB/TiB conversion; a mirror-based layout can be much smaller. The case does not determine RAID capacity.

Our verdict: choose the case around the storage architecture

Best for compact four/five-HDD builds: Jonsbo N2. Best for six drives and easy component choice: Fractal Node 304. Best for six HDDs with micro-ATX flexibility: Jonsbo N4. Best balanced compact eight-HDD shortlist: Jonsbo N3. Best for eight front hot-swap trays: SilverStone DS380, with particular attention to cooling and backplane wiring. These are recommendations based on published specifications and build constraints, not a ranking from physical testing.

Buy the chassis only after deciding the number of protected drives, the motherboard/HBA topology, the network card, the PSU cable route and how you will replace a failed disk. Spending a little more on a case that allows accessible cables and sensible airflow can be better value than choosing the smallest enclosure and paying later to rebuild the entire NAS.

Related ESP32 Guides

Manufacturer specifications and technical references

CONTINUE EXPLORING / NAS & HOME SERVERS

Read next

Practical guides related to this article.

Explore the topic →
HARDWARE DECISION GUIDEPlanning your next NAS upgrade?

Compare hardware, storage and software before buying.

Compare options →