Quick Summary (TL;DR):
To size a UPS for a NASPriceAliExpress price, router and home server, check both VA (volt-amperes) and watts on the UPS label. The connected equipment must stay below both output limits, with sensible headroom for load spikes and expansion. Then check the manufacturer’s runtime-at-your-actual-watt-load chart: a 1000VA UPS does not provide a fixed number of minutes, and a bigger VA rating does not automatically mean a bigger battery. Measure the whole protected setup with a power meterPrice, include hard-drive start-up and server peaks, and pick a USB/SNMP/NUT-compatible UPS that can trigger a clean NASAliExpress price or VM shutdown. For many homes, preserving the NASAliExpress price, router and essential switch long enough to shut down safely matters more than attempting to run every device for an hour. The worked examples below are illustrations, not measured product benchmarks or promised runtimes.
UPS VA vs Watts: The Two Ratings That Matter
A UPS — an uninterruptible power supplyPrice — sits between mains electricity and your devices. When the input fails, the inverter and battery keep its battery-backed outlets powered for a limited time. For a home NAS, the critical outcome is not simply staying online: it is avoiding an abrupt loss of power during file writes, virtual machine operations or a storage-pool update.
UPS listings often put 700VA, 1000VA or 1500VA in the largest type, while hiding the actual output watt limit several lines down. That creates the classic shopping mistake: buying a “1000VA” unit without noticing it might be rated at only 600W, or assuming it will run a 100W NAS for ten times as long as a 1000W device.
There are three separate decisions: can the UPS supply the required power? how long can it supply that power? and can it notify your equipment to shut down before the battery is exhausted? The first is determined by watts and VA; the second by model-specific batteries, inverter behaviour and load; the third by supported communication and software.
| Specification | What it means | Why you should care |
|---|---|---|
| Watts (W) | Real electrical power drawn by the load | The UPS must support total real power, including peaks |
| Volt-amperes (VA) | Apparent power: RMS voltage × RMS current | Another independent output limit; not “battery minutes” |
| Output power factor / W-to-VA rating | UPS rated watts ÷ UPS rated VA | Explains why two 1000VA models can have different watt limits |
| Runtime curve | Manufacturer estimate in minutes versus load in watts | Directly informs your minimum shutdown window |
| USB/SNMP/NUT support | UPS status and shutdown signalling | Allows NAS/servers to act before the battery is empty |
| Battery rating (Wh or V × Ah) | An indication of stored energy, not delivered runtime | Useful context, but not a replacement for published curves |
APC explains that both the watt limit and VA limit have to be respected. Eaton likewise treats capacity and runtime as distinct UPS sizing questions. See the linked manufacturer buying and sizing guides in the sources section.
The Difference Between VA and Watts, Without the Marketing
Watts represent useful or real input power consumed over time. VA represent the product of RMS voltage and RMS current. For many AC-powered electronic loads, voltage and current are not perfectly aligned or the current is not a clean sine wave, so apparent power can exceed real power.
For a single load, an effective power factor can be expressed as PF = watts ÷ VA. You can rearrange this to estimate VA = watts ÷ PF. This is a useful planning relationship, not permission to invent the power factor of your NAS or adapter.
Power factor (PF) = real power (W) / apparent power (VA)
Example: 120 W at PF = 0.80
VA = 120 / 0.80 = 150 VA
Example: 120 W at PF = 0.60
VA = 120 / 0.60 = 200 VA
UPS example: 1000 VA / 600 W
Both of these limits apply simultaneously.
Those PF values are hypothetical. Power factor depends on the power supply, load level and power electronics. A true-RMS meter that reports real watts and power factor can help; a basic watt meter that displays only W cannot tell you the measured VA.
At mains voltage near 230V, dividing a device’s real watts by 230V does not always produce its actual AC current, because apparent power and waveform shape matter. A server power supply also has conversion losses, meaning the PSU’s DC output nameplate is not the same as the real watts drawn from the wall.
An Important Distinction: UPS Output PF Is Not Your Server’s PF
A 1000VA / 600W UPS has a rated output W/VA ratio of 0.6. That number describes the UPS manufacturer’s two maximum output ratings. It does not prove that the connected equipment has a power factor of 0.6, nor does it mean that every 1000VA unit is rated for 600W.
For instance, some enterprise-oriented models advertise close to one watt per VA; a documented 230V CyberPower PR1000ERT2U is rated at 1000VA and 1000W. Other UPS families operate at lower watt-to-VA ratios. Always compare the exact regional product model and data sheet — not a generic family name or US electrical specifications on a UK/EU store listing.
Never plan to load either rating to its absolute maximum. APC suggests watt capacity roughly 20–25% above the connected load in its buying guide; Eaton recommends at least 15% VA capacity above the calculated requirement. We use a simple 25% planning margin for both values in the examples below, and more where growth or start-up loads justify it.
Step 1: Decide Which Devices Really Need Battery Backup
A NAS rack or smart-home corner often contains equipment that is nice to have during a power cut and equipment that is essential to a clean shutdown. They are not the same list. Running your monitor, television, printer, desktop speakers and unrelated chargers from the same battery can steal the minutes your disks need for a safe shutdown.
| Device | Normally on battery-backed outlets? | Reason / caveat |
|---|---|---|
| NAS and its required external storage | Yes | Must retain power until clean shutdown; count any USB DAS and disk shelves |
| Mini PC / hypervisor host | Yes | VMs and containers must shut down without power loss |
| Router / firewall | Usually | Needed for remote alerting, administration and network UPS signalling |
| Small switch serving UPS clients | Usually | Critical if NUT/SNMP messages travel through it |
| Wi-Fi access point | Only if useful | Protect one AP if wireless-only management depends on it |
| Plex television or desktop monitor | Normally no | Not required to protect data; avoid unnecessary load |
| Laser printer, heater or high-inrush appliance | No | Often inappropriate for small UPS outlets and may overload inverter |
Remember the hidden components: a NAS using a powered USB disk enclosure requires that enclosure’s PSU to remain energised until the NAS has finished its writes. A PoE switch can have a modest chassis load plus significant attached camera and access-point consumption. A network switch with an important NUT client should not lose power before that client receives the shutdown signal.
Step 2: Measure the Entire Setup at the Wall
Nominal processor TDP, adapter wattage and PSU ratings are poor proxies for the total AC consumption of a working home server. A mini PC sold with a 65W power brick is not necessarily drawing 65W continuously, and a server equipped with a 500W PSU is not necessarily using 500W at idle. Conversely, idle measurements alone can miss the worst load.
- Use a plug-in energy meter suitable for your local mains voltage and current rating; record watts, and ideally VA/PF, at the wall.
- Measure devices separately when practical. Record the whole stack during idle operation, scheduled backups and file copies, normal media streaming, and any demanding VM or transcoding workload.
- For a multi-bay NAS, note the load while all disks are awake, while a RAID scrub/rebuild is running and during the normal boot or restart sequence.
- Add equipment you will actually connect to battery-backed outlets; do not count devices connected only to surge-protected outlets in battery runtime.
- Apply a planning allowance for future disks, higher-CPU workloads or a second switch. Use device data sheets to understand brief inrush that a slow display may not capture.
- Keep a note of your observed maximum steady load and separately investigate any unusually high start-up or transient requirements.
For the decision to buy a larger UPS, use the realistic protected equipment load — not a theoretical sum of the maximum printed wattages on all PSU bricks. However, treat documented high start-up draw and overload limits seriously. A five-second peak and a continuous 15-minute load create different risks.
If you have no meter yet, prepare a cautious provisional calculation from actual device consumption documentation and upgrade the estimate once you can measure it. A £15–£30 style power meter may be a better first purchase than a much larger UPS selected by guesswork; prices vary, so do not use that illustrative range as a current price quote.
Step 3: Calculate the Minimum UPS Watt and VA Ratings
Begin with measured or justified watts and, where possible, measured VA. Next reserve capacity. We use 1.25× here as a practical starting point for steady-state load, not an electrical standard and not a substitute for the specific UPS maker’s guidance.
Minimum planned UPS watts ≈ total protected watts × 1.25
Minimum planned UPS VA ≈ total protected VA × 1.25
Choose a model rated ABOVE BOTH values.
Then check the actual runtime curve, USB/SNMP support,
input/output plugs, battery maintenance and start-up peaks.
If your meter does not provide VA, estimating apparent power from an assumed PF is less reliable. Use a conservative provisional PF only as a sensitivity check and then measure it or ask the manufacturer where the load is demanding. Also do not simply add single-device VA figures to claim a precise combined reading: that sum is a conservative screening tool because their current waveforms need not add arithmetically.
Worked Example: Four-Bay NAS, Router and Switch
Imagine a four-bay NAS backing up family photos, a broadband router and a small Ethernet switch. The following wattages are invented example measurements to show the method; they are not measurements of particular Synology, QNAP or UGREEN products.
| Equipment | Illustrative measured load |
|---|---|
| Four-bay NAS during disk activity | 60W |
| Broadband router / firewall | 15W |
| Small unmanaged switch | 10W |
| External backup HDD, if used during backup | 10W |
| Total with all four devices | 95W |
| Total with 25% watt margin | 118.75W |
Even a relatively small UPS with a 300W or 400W real-power rating might provide substantial output headroom for this example. That is not a guarantee of a long runtime. Compare the manufacturer’s runtime chart at roughly 95W, determine how long the NAS really takes to shut down and check support for USB status reporting. Many 600–850VA units can be electrically adequate for such a load, but their runtimes and communication features vary considerably.
If you want to keep broadband online during a long outage, consider whether the entire path is protected. A powered optical network terminal (ONT), fibre modem or separate PoE access point might otherwise fail before the router; meanwhile, an external street cabinet losing electricity can still interrupt Internet access even when the home equipment has battery power.
Worked Example: Home Server, NAS and PoE Network
Now consider a larger setup with a Proxmox mini server, a NAS, router and PoE networking. Again, these are illustrative loads only, not a benchmark or a suggested specific UPS model.
| Equipment | Illustrative active load |
|---|---|
| Home server under representative VM load | 145W |
| Six-drive NAS carrying out a backup | 95W |
| Router / firewall | 20W |
| PoE switch including attached devices | 85W |
| ONT / fibre modem | 10W |
| Total active load | 355W |
| Total with 25% watt margin | 443.75W |
If this stack’s combined measured power factor were hypothetically 0.85, it would represent roughly 418VA before headroom and 522VA with 25% margin. On those steady-state figures alone, a 1000VA / 600W UPS would clear both minimum ratings, but there is still no assurance that it supplies the required battery runtime or handles startup transients. A larger model may be justified by runtime charts, redundancy needs, growth or heavier-than-assumed loads.
The PoE segment is a good reason to measure instead of relying on the switch’s box label: “120W PoE budget” indicates a supported delivery budget, not that every installed device always consumes 120W. Add the switch’s own overhead and actual connected loads. Likewise, hardware transcoding or new VMs can increase server draw noticeably.
Step 4: Read the Runtime Curve — VA Cannot Tell You the Minutes
A UPS can satisfy the electrical output ratings yet still run out of battery before applications shut down. Published runtime curves are therefore the deciding specification after watt and VA compatibility. Reputable manufacturers provide model-specific tools or graphs where you enter the load in watts and inspect the estimated minutes on battery.
Two 1000VA products can contain different battery configurations and have different inverter efficiencies. One may be designed for a compact home office and another for a rack. They can have radically different runtime at the same 100W or 350W load. Nor should you assume that doubling the UPS VA rating doubles runtime: it might only raise maximum inverter output.
- Find the exact model number and electrical region (for example, the 230V UK/EU variant, not an American 120V SKU).
- Find the official runtime table/curve or manufacturer UPS selector for that exact variant.
- Read the predicted runtime at the wattage of the actual battery-backed load, not at 50% load unless that is genuinely your operating point.
- Ensure enough time exists for your chosen failure response plus NAS/VM shutdown with reserve. A new-battery manufacturer curve is a planning reference, not a field guarantee.
- Check the UPS battery health and age; higher room temperature, older lead-acid batteries, repeated deep discharges and configuration differences can reduce actual time.
- Confirm the software will act before the battery becomes critical, then perform a controlled end-to-end test.
Eaton’s official runtime graph for its 5E1100IUSB demonstrates the load-versus-minutes relationship and warns that actual runtime varies with battery age and temperature. Use the shape and manufacturer’s own figures for your candidate unit; do not transplant another model’s chart.
Why V × Ah / Watts Is Only a Crude Runtime Estimate
You may see DIY calculators dividing battery watt-hours by load watts. A battery marked 12V × 9Ah has a nominal energy figure of 108Wh. A UPS with two such batteries has a simple nameplate product of 216Wh. But those numbers do not mean you will receive 216Wh at an AC outlet.
Naive battery energy example (not a runtime promise):
2 batteries × 12V × 9Ah = 216Wh nominal
216Wh / 120W = 1.8h = 108 minutes (IDEALISED ONLY)
Real UPS runtime is shorter and load-dependent because:
- battery capacity varies with discharge rate
- inverter/transformer losses consume energy
- UPS electronics draw power
- low-voltage cut-off leaves battery reserve
- temperature and battery ageing matter
Use the manufacturer model-specific runtime curve instead.
The rated amp-hour capacity of lead-acid batteries is typically measured under specified test conditions, often at a slow discharge rate. Under substantial inverter loads, usable energy can be lower; battery-management thresholds and losses further reduce delivered AC energy. A homemade formula cannot safely replace the published curve and a real shutdown test.
Step 5: Define the Shutdown Window, Not an Arbitrary Hour
For most home NAS use, the practical objective is enough time to detect mains failure, let short dips clear, and shut down storage and hosts cleanly. If you genuinely need uninterrupted Internet, cameras, or a production service for one hour, that is a different energy-storage requirement and may warrant a higher-capacity UPS or a dedicated power solution.
Build a timeline backwards from the minimum manufacturer-estimated runtime at your measured load. Include application quiescence and host shutdown rather than setting a timer that fires only when the battery has almost expired. For example, consider a hypothetical UPS chart showing 20 minutes at the planned watt load:
| Illustrative elapsed time | Action | Why it matters |
|---|---|---|
| 0 minutes | Utility power fails; UPS switches to battery | UPS and network communication stay live |
| 1–2 minutes | Confirm outage is sustained; automatic notification | Avoid unnecessary shutdown on split-second disturbances |
| 2–4 minutes | Stop demanding services; tell virtual machines to shut down | Leave time for database and file flushes |
| 4–7 minutes | Stop hypervisor / NAS cleanly | Storage goes offline before battery runs out |
| 7–20 minutes | Unused planning reserve | Protects against slow shutdown, ageing or lower real runtime |
That schedule is not a recommended hard-coded configuration: you must measure your own shutdown duration and adjust for the model’s actual runtime. A very small UPS might provide far less than 20 minutes at the chosen load, requiring near-immediate shutdown. A larger unit could support several minutes of outage tolerance. Never rely solely on “shut down at 15% battery” if the remaining runtime at that battery level is shorter than the system’s clean shutdown.
What About Hard-Drive Spin-Up and Start-Up Power?
A NAS with several mechanical drives can draw more power during simultaneous spin-up than during idle operation. A UPS that copes with 80W of normal use might encounter a larger momentary demand when all disks restart after a planned reboot. Enterprise servers and some PSUs can also have short inrush currents.
UPS output overload behaviour depends on the design and the duration of the overload. Some products can tolerate brief peaks; others transfer, beep or cut output. Do not assume that an ordinary plug-in meter sampling every second will capture milliseconds of inrush. Use the NAS/storage technical specifications, vendor UPS selection guidance and a controlled start-up test with the intended protected devices.
Many NAS units support staggered HDD spin-up or power recovery settings, but availability varies by model and firmware. Do not change those settings without considering the storage controller and recovery sequence. The safest buying approach is generous electrical headroom plus manufacturer-documented start-up compatibility.
Line-Interactive vs Offline vs Online UPS
| UPS topology | Typical role at home | Main consideration |
|---|---|---|
| Standby / offline | Low-cost backup for simple networking devices | Transfer behaviour and waveform depend on exact model |
| Line-interactive with AVR | Often a strong fit for NAS, router and compact server | Can correct some voltage fluctuations without battery discharge |
| Online double-conversion | More demanding loads or unstable supply | Usually higher cost and possibly higher continuous losses/noise |
AVR means automatic voltage regulation. A line-interactive UPS may use a tap-changing transformer to correct modest low or high input voltage without consuming battery energy every time. It does not change the need to consider runtime, battery condition, and communication support.
Pure sine-wave output is worth investigating for modern server power supplies with active power factor correction. Schneider Electric and CyberPower document compatibility considerations with simulated or stepped waveforms. That does not mean every stepped-wave UPS fails with every mini PC; it means you should choose a compatible model and preferably test the actual hardware combination.
An online UPS is not automatically better for a quiet home office: consider acoustic noise, energy losses, physical space, battery replacement cost and whether its benefits are needed for your electrical environment.
USB, SNMP and Network UPS Tools: The Part Buyers Forget
A UPS plugged into a NAS only by its power cable may keep the machine running until the battery empties, but it may have no way to inform the NAS that the mains has failed. For unattended protection, choose a supported path to read UPS status and trigger shutdown.
- USB UPS: one NAS or server communicates directly with the UPS using a compatible USB interface and driver; check the exact device and OS.
- Network UPS/SNMP: an appropriate network-management module can publish UPS status across the LAN; verify model, module and software support.
- NUT: Network UPS Tools allows one UPS-facing system to serve status to other client systems. A common deployment has the directly connected host acting as the primary server and other hosts as secondary clients.
- Vendor network UPS feature: some NAS interfaces expose a server/client workflow under their power menus, with restrictions on supported devices and network topology.
Both the UPS and the systems that need to receive its status must retain a working communication path while mains power is unavailable. If your NAS acts as a network UPS server but its Ethernet switch is plugged into a non-battery outlet, secondary servers may never receive the event. If the primary NAS shuts off before the clients have completed their work, their shutdown sequence can also fail.
USB status cable
|
[UPS with battery]
| | |
NAS mini-PC router + switch
| | |
+-------+---------+
LAN
NAS / UPS host: primary NUT or vendor network-UPS server
Mini-PC / second NAS: NUT or supported vendor client
All equipment in the signalling path needs battery-backed power.
NUT’s official documentation describes the primary and secondary monitoring roles and shows port 3493/tcp for the UPS status service. Keep that service restricted to your trusted local network and use supported authentication/security controls. This article is about sizing; detailed NUT shutdown configuration is covered in our NUT and Home Assistant shutdown guide.
Synology UPS Compatibility and Shutdown Behaviour
Synology maintains a UPS compatibility list and states that supported units can provide UPS service to another Synology product through the Network UPS Server feature. In DSM, UPS settings are found under Control Panel > Hardware & Power > UPS on supported versions. Firmware changes and exact model identifiers matter; do not assume a USB UPS works just because its battery can power the NAS.
Plan to confirm UPS detection, decide when the NAS should enter safe mode, and check the power-off and recovery behaviour for your specific DSM version. Synology notes that the UPS power-off function varies by brand and model and recommends a simulated power-outage test. The NAS may appear switched off to clients while still drawing some power depending on its safe-mode behaviour and UPS configuration.
QNAP UPS Compatibility and Shutdown Behaviour
QNAP QTS 5.2.x documentation places UPS configuration under Control Panel > System > External Device > UPS. Depending on the installation, supported choices include USB connection, SNMP and network UPS slave. The user can choose a timed power-off or auto-protection behaviour.
QNAP explains that auto-protection stops services and unmounts volumes to protect data. A system that has unmounted storage may still need power until the configuration and UPS execute the intended further action. The safe workflow is to verify the timing and expected final power state rather than treating “auto-protection” as identical to complete electrical shutdown.
UGREEN NASync UPS Compatibility and Shutdown Behaviour
UGREEN UGOS Pro has a dedicated Control Panel > Hardware & Power > UPS area. UGREEN documents USB, SNMP and Network UPS Slave methods on supported systems, plus Standby Mode and Auto Shutdown. Its NUT Server workflow can relay UPS events to additional network clients.
The exact capability depends on your UGREEN NAS model, UGOS Pro version and UPS compatibility. UGREEN’s compact DC UPS products also have particular voltage/power requirements: they cannot be substituted indiscriminately for a normal mains-output UPS feeding a NAS, separate router, switch and server. Check the official compatibility list and wiring guide before purchase.
A Practical Pre-Purchase UPS Checklist
- Electrical ratings: the exact 230V regional model provides enough output watts and VA with margin.
- Published runtime: there is a manufacturer curve at your intended watt load showing enough minutes for the measured shutdown sequence.
- Usable outlets: enough battery-backed sockets in the correct UK/EU IEC/Schuko/UK format, without unsafe adaptors or improvised wiring.
- Compatible UPS signalling: USB HID / supported driver, documented SNMP or supported network UPS role for the NAS/host.
- Output waveform: compatible with the intended PSU(s), especially when active-PFC server hardware is involved.
- Input voltage and battery replacement: appropriate mains voltage, replaceable battery model, local service availability and replacement cost.
- Topology and noise: line-interactive or online type fits the environment, including audible alarms, fans and expected power losses.
- Recovery: known behaviour when utility power returns, including NAS BIOS power-recovery and possible delayed sequential startup.
- Growth: spare watt/VA margin and a realistic allowance for extra HDDs, PoE loads or another mini PC.
- Testing: the selected UPS can be tested with a controlled outage without taking unacceptable risks.
If you are deciding between APC, Eaton and CyberPower families, use our APC vs CyberPower vs Eaton UPS buying comparison for model-level differences. A brand name alone tells you neither the runtime nor the exact NAS compatibility.
How to Test a UPS Without Risking Your Data
A live test is valuable, but do not repeatedly pull plugs from a busy storage array or carry out a deep battery discharge just to see whether the UPS display is accurate. Start with a small, low-risk test and record the result.
- Charge the UPS for the period required in its instructions, install any monitoring software and verify that UPS status is visible on the NAS or UPS host.
- Back up important data and stop large writes, rebuilds, scrubs, backups, virtual machines or any workload that would make interruption costly.
- If the vendor supports it, run a built-in self-test first and check for overload or battery warnings.
- During a maintenance window, simulate loss of mains input to the UPS following manufacturer guidance; keep the UPS output and USB/network monitoring connected.
- Observe whether all intended battery-backed devices remain powered and whether the NAS receives an on-battery event.
- Check that server guests, the host OS and NAS storage close in the planned order before the UPS approaches a low-battery condition.
- Restore mains power, check the UPS returns to normal charging, and verify file systems, storage pools and network services.
- Document measured shutdown duration and reported remaining battery runtime; adjust the trigger so there is reserve rather than relying on a single test result.
For systems you cannot safely interrupt, conduct a staged validation on a spare test device or during a supervised maintenance period and follow the UPS/NAS manufacturer’s procedure. A successful test with a new battery is not proof that the same timing will work three years later.
Battery Age, Room Temperature and Replacement Costs
Small UPS models commonly use sealed lead-acid batteries, although battery chemistry varies. APC states that its typical VRLA UPS batteries last about three to five years, depending strongly on temperature, loading and discharge history. A hot cupboard above the fridge or an unventilated rack can shorten useful service life.
Battery serviceability should influence total cost. Find the replacement cartridge part number and local availability before buying; a low-cost unit with a proprietary battery or no practical replacement path may become expensive over five years. Follow manufacturer instructions for safe disposal and replacement; do not open a UPS power section or improvise internal wiring, which can carry hazardous voltages even when unplugged.
Test or inspect periodically, especially after a long outage. Many UPS units self-test, but a passed self-test is not a guarantee of your target runtime under full system load. A unit that begins alarming, offers only a few minutes, or shuts off during a normal test needs attention before it is trusted with live backups.
How Much Electricity Does the UPS Itself Use?
A UPS introduces conversion, charging and standby overhead in addition to whatever the attached NAS and networking hardware consume. The idle/online losses differ significantly by topology and model; there is no honest universal “one UPS uses X watts” rule. Compare the manufacturer’s efficiency data where available and measure the complete installation if electricity costs matter.
A small always-on difference matters over a year. For example, 10W of extra continuous consumption is 87.6kWh annually (0.010kW × 24 × 365). Multiply that by your own electricity unit tariff to estimate annual energy cost; add any relevant fixed charges or taxes only when calculating your complete bill. This is a calculation example, not a measured overhead for APC, CyberPower or Eaton hardware.
Our NAS and home-server electricity-cost guide covers how to compare 24/7 devices using measured wall consumption.
Common UPS Sizing Mistakes
- Buying by VA alone: a “1500VA” label does not guarantee the number of watts or minutes you need.
- Confusing a PSU rating with normal consumption: a 650W server power supply rating does not mean 650W is continuously drawn, yet input peaks still matter.
- Omitting router/switch/ONT power: network UPS clients or remote alerts can fail when the communications path loses electricity.
- Putting only the NAS on battery: a separate powered disk enclosure can abruptly stop while the NAS is still writing.
- Buying a USB UPS without supported communication: a UPS may power the NAS but fail to signal safe shutdown.
- Assuming 50% load runtime describes your setup: the 50% point differs by model; enter your measured W instead.
- Waiting until 1% battery to shut down: the OS, hypervisor or disks may still be busy when power disappears.
- Expecting a NAS UPS to replace backups: lightning, theft, corruption, failed batteries and mistakes can still destroy data.
- Reusing a years-old runtime chart: age, replacement battery, firmware and model revision can change the outcome.
- Connecting printers or motors to battery sockets: excessive startup/inrush or sustained demand may overload smaller units.
Frequently Asked Questions
Is a 600VA UPS enough for a two-bay NAS and router?
It can be, provided the actual watt and VA loads fit below that model’s limits, the expected runtime covers the full shutdown process, and the UPS can notify the NAS. Some 600VA products have relatively low watt output and minimal batteries. The only credible answer comes from the exact model data sheet and measured load.
Is 1000VA the same as 1000W?
No. A 1000VA model might be rated at 600W, 700W, 900W or 1000W depending on its design. The exact watts are printed in the product specifications. Even a 1000VA/1000W unit has model-dependent runtime.
Can I simply use a bigger UPS and get twice the runtime?
Not necessarily. More rated output capacity may only mean the UPS can drive a larger load. Battery chemistry, internal battery size, inverter design and the model’s supported expansion batteries determine runtime. Compare curves at the same number of watts.
Does a NAS need pure sine wave output?
Many modest NAS and router supplies function on different UPS waveform types, but some active-PFC server power supplies have compatibility constraints. Pure sine-wave models are a sensible preference where PSU compatibility is uncertain or a high-value server is involved; verify the manufacturer’s electrical guidance for your equipment.
How many minutes should a NAS UPS provide?
Enough time for your selected delay, service and VM shutdown, storage flush/unmount, and a reserve for battery ageing. Some installations deliberately shut down within a minute or two; others require a 10–15-minute operational window. There is no universal minute figure. Measure your actual sequence and choose the runtime curve accordingly.
Can one USB UPS shut down two NAS units?
Yes, in compatible systems. One NAS or server can connect directly to the UPS and relay status to secondary systems using a supported vendor network UPS service or Network UPS Tools. The switch/router carrying notifications needs battery power, and the client shutdown timing must precede loss of the primary server.
Will a UPS protect against every power-related data loss?
No. It mitigates short outages and allows graceful shutdown when configured correctly. It does not prevent ransomware, accidental deletion, hardware failure or every surge event. Keep independent backups — see our NAS 3-2-1 backup plan.
Final Recommendation: Buy for Load, Runtime and Shutdown — in That Order
For a home NAS and router, start by protecting only the equipment essential to preserve data and communication. Measure that setup, size the UPS above both watts and VA with appropriate headroom, and select the actual battery runtime at the measured wattage from the manufacturer’s model-specific curve. Then confirm supported USB/SNMP/NUT shutdown signalling and test the complete sequence.
A 1000VA box chosen from a headline rating is a guess; a 700VA unit with sufficient real-power capacity, documented runtime and tested USB shutdown may be a better fit for a light NAS. A busy Proxmox server, PoE cameras and a six-drive NAS may justify a significantly larger unit. The defensible choice is the one with verified figures for your load — not a generic UPS-size rule.
Related Guides on esp32.co.uk/
- Best UPS for Home Assistant, Router and NAS
- APC vs CyberPower vs Eaton UPS for Home Servers
- Network UPS Tools with Home Assistant and NAS: Safe Automatic Shutdown
- NAS and Home-Server Electricity Costs: Choosing Efficient Hardware
- A 3-2-1 NAS Backup Plan: USB Drive, Second NAS and Cloud
Official Manufacturer Documentation and Technical References
- APC / Schneider Electric — UPS Buying Guide: watts, VA, power factor and headroom
- Eaton — UPS sizing guide: capacity, VA calculation and runtime
- Eaton — example model-specific UPS runtime chart (5E1100IUSB)
- APC — Expected life of a UPS VRLA battery and temperature sensitivity
- Schneider Electric UK — Active-PFC PSU considerations with stepped-wave UPSs
- CyberPower EU — example PR1000ERT2U output watt and VA ratings
- Synology — Official UPS compatibility list and Network UPS Server notes
- QNAP — Configuring UPS settings on QTS 5.2.x
- UGREEN UGOS Pro — Hardware & Power / UPS settings
- UGREEN — NUT Server and network UPS client configuration
- Network UPS Tools — upsmon primary/secondary monitoring and shutdown
- Network UPS Tools — Official documentation