Quick summary: M5Stack launched the Chain Captain on 20 November 2026 as a US$35 handheld controller for its UART-based Chain Bus modules. The ESP32-S3 device combines a 1.54-inch screen, physical controls, audio, infrared, motion sensing and an 800mAh battery in one programmable unit.
The Chain Captain, product code C160, is now listed for sale by M5Stack. It is not a new Espressif chip or radio module: it is a complete M5Stack development controller built around an ESP32-S3R8 and intended to act as the master for a daisy chain of Chain-series sensor, input and output nodes.

What Chain Captain actually is
M5Stack has given the controller enough local hardware to run as a portable interface rather than merely bridging a cable to a PC. Its ESP32-S3R8 runs a dual-core Xtensa LX7 processor at up to 240MHz, with 16MB of flash and 8MB of PSRAM. The manufacturer lists 2.4GHz Wi-Fi, but does not list Thread, Zigbee or Ethernet connectivity.
- 1.54-inch 240×240 colour LCD driven over SPI
- Three user keys, a power button and a programmable RGB LEDPriceAliExpress price
- ES8311 audio codec, analogue MEMS microphone and 1W speakerPriceAliExpress price
- BMI270 six-axis IMU and RX8130CE real-time clock
- Infrared transmitter and receiver
- USB-C, one Chain port, one Grove port and a 15-pin expansion port
An 800mAh battery is built in. Power is managed by the M5PM1 and M5IOE1, with wake-up sources including the keys, IMU, RTC and external I/O. The M5PM1 is the same power-management device covered in our M5Stack Stamp Timer Power2 report. M5Stack publishes point measurements for standby and full-load current, but those figures are not a general battery-life claim; display brightness, Wi-Fi activity, audio and attached nodes will all change runtime.
Chain Bus is UART, not Matter or Zigbee
The important feature is the Chain port. M5Stack’s Chain nodes use a UART serial daisy-chain protocol, allowing modules to be connected one after another instead of each occupying a separate host connector. The range already includes keys, joysticks, switches, buzzers, LEDPrice matrices, servos and sensors. A new Chain ENV node, released alongside the Captain, measures temperature, humidity and pressure.
M5Stack says the Captain detects supported modules on the chain and presents them on its screen. The official M5Chain Arduino library is published under the MIT licence, and the documentation includes UiFlow2 and Arduino examples. That makes the product more approachable than a bare UART wiring exercise, but the convenience applies to supported Chain devices and software. It should not be read as generic plug-and-play discovery for arbitrary UART peripherals.
Nor does the ESP32-S3 automatically make this an ESPHome or Home Assistant product. M5Stack’s launch materials describe smart-home controller uses, but they do not announce native ESPHome support or a ready-made Home Assistant integration. Any such deployment would need an appropriate firmware and integration path.
Price, availability and practical fit
M5Stack’s official shop listed the Chain Captain in stock at US$35 when checked on 21 November, with shipping calculated at checkout; tax and regional distributor pricing may differ. The package contains the controller itself. Chain nodes are separate purchases.
The strongest use case is a small, battery-powered control panel or data terminal that needs several physical modules without a custom carrier board. Audio, IR, an IMU and an RTC also open up remote-control, alarm and interactive-display projects. Makers comparing other recent M5Stack controllers can also see the CoreMatrix ESP32-C61 launch and the PaperDIY ESP32-S3 e-paper kit.
There are clear limits. M5Stack lists a 240×240 LCD and three keys, not a touch panel. The Chain connector is a UART ecosystem port rather than a general-purpose substitute for every Grove or I2C accessory, and there is only one Chain port on the controller. For projects already committed to Chain modules, however, the Captain provides a much more capable master than a basic serial bridge.


